Apple Xserve (Early 2008) DIY Procedure for Fan Array wi Manuale Utente Scaricare il pdf

 Xserve (Late 2006/Early 2008)

073-1100 Rev. B

Fan Array

Replacement Instructions

Follow the instructions in this document carefully. Failure to follow these instructions could

damage your equipment and void its warranty.

Online instructions are available at http://www.apple.com/support/diy/.

Working Safely Inside the Xserve

Always touch the Xserve enclosure to discharge static electricity before you touch any

components inside the Xserve. To avoid generating static electricity, do not walk around the

room until you have nished working inside the server and have replaced the cover. To minimize

the possibility of damage due to static discharge, wear an antistatic wrist strap while you work

inside the Xserve.

Warning: Always shut down the Xserve and disconnect the power cords before opening

it to avoid damaging its internal components or the components you are installing. Don’t

open the server while it is turned on. Even after you shut down the Xserve, its internal

components can be very hot. Let it cool before you open it.

Tools Required

The only tool required for this procedure is a Phillips #1 screwdriver.

Removing the Xserve from a Rack

Alert users that the server will be unavailable for a period of time. 1.

Shut down the Xserve (see the Xserve User’s Guide for help) and then wait to let the Xserve 2.

internal components cool.

Warning: Always shut down the Xserve before opening it to avoid damaging its internal

components or the components you want to install or remove. Don’t open the Xserve

or try to install or remove items inside while it is turned on. Even after you shut down

the Xserve, its internal components can be very hot. Let it cool down for 5 to 10 minutes

before you open it.

1 2 3 4 5 6 7

Sommario

Pagina 1 - Fan Array

 Xserve (Late 2006/Early 2008)073-1100 Rev. BFan ArrayReplacement InstructionsFollow the instructions in this document carefully. Failure to follow t

Pagina 2 - Opening the Xserve

Xserve (Late 2006/Early 2008) Fan Array Replacement Instructions 2Unplug all cables from the Xserve. 3. Note: If you have trouble releasing a cable f

Pagina 3 - Airow Duct

Xserve (Late 2006/Early 2008) Fan Array Replacement Instructions 3Removing the Installed Fan ArrayNote: Before you can remove the fan array, you must

Pagina 4

Xserve (Late 2006/Early 2008) Fan Array Replacement Instructions 4Fan ArrayLoosen the two thumbscrews that secure the fan array to the enclosure. 1.

Pagina 5

Xserve (Late 2006/Early 2008) Fan Array Replacement Instructions 5Installing the Replacement Fan ArrayInstall the foam included in the replacement pa

Pagina 6

Xserve (Late 2006/Early 2008) Fan Array Replacement Instructions 6Lower the airow duct into position on the logic board. 4. Note: When installing th

Pagina 7 - Closing the Xserve

Xserve (Late 2006/Early 2008) Fan Array Replacement Instructions 7Closing the XserveReplace and secure the cover.1. Slide the Xserve back into the ra

Commenti su questo manuale

Nessun commento

Apple Xserve (Early 2008) DIY Procedure for Fan Array wi Manuale Utente

Navigare online o scaricare Manuale Utente per Software Apple Xserve (Early 2008) DIY Procedure for Fan Array wi. Apple Xserve (Early 2008) DIY Procedure for Fan Array with Foam User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Software Apple Xserve (Early 2008) DIY Procedure for Fan Array wi