Apple LaserWriter Select 310 Specifiche Pagina 47
- Pagina / 256
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Flowcharts and TablesTroubleshooting
Yes
START
No
1. Switch off the printer and disconnect it from the
Macintosh computer.
2. Remove the top cover, rear cover, and side covers.
3. Remove the I/O shield and I/O board.
4. Plug in and switch on the printer.
Does
the fan
come on?
Does the
fuser bulb glow every
few seconds during
startup?
Go to Table 2,
No Power to Fan.
Go to Table 3,
Fuser Assembly
Failure.
No
Yes
Does the
main motor
rotate sometime
after startup?
Initiate a service test page.
Go to Table 1,
Main Motor
Failure.
Yes
No
A
LaserWriter Select 300 Flowchart 2
- LaserWriter Select 1
- Paper Path 3
- Sensing System 4
- Interface Connectors 5
- LaserWriter Select 300 6
- LaserWriter Select 310 7
- LaserWriter Select 360 8
- LaserWriter Safety 9
- Specifications 12
- Intro Dates 14
- Logic Board 15
- Performance 17
- Built-In-Fonts 18
- Electrical 19
- Physical 20
- Environmental 21
- Troubleshooting 23
- Troubleshooting Tips 25
- Service Test Page 26
- Test-Ready Configuration 28
- 310/360 Power-On Self Test 30
- 360 Printer Diagnostic 32
- Circuit Board Diagrams 34
- ROMs (1 or 2) 36
- Cassette Feeder Board Diagram 40
- RTN1 RTN2 P11 42
- Select 360 Fax Card 43
- Wiring Diagram 44
- OPTIONAL FEEDER 45
- Important 57
- Table 1. Main Motor Failure 57
- Table 2. No Power to Fan 58
- No Power to Fan (Continued) 59
- No Power to Fan (Continued) 60
- Table 15. All-Blank Page 75
- All-Blank Page (Continued) 76
- Table 16. All-Black Page 76
- All-Black Page (Continued) 77
- Table 17. Light/Faded Image 77
- Light/Faded Image (Continued) 78
- Table 23. Ghosting 84
- Ghosting (Continued) 85
- Table 24. Bad Fusing 85
- Multipurpose Tray 93
- Take Apart 95
- Top Cover 96
- Captive Screw 97
- Side Covers 98
- Left Side Cover 99
- Right Side Cover 100
- Rear Cover 101
- Manual Feed Tray 103
- Cassette Feeder 105
- Assembly 105
- Right Bottom 110
- White Cassette Gears 112
- Solenoid 113
- Cassette Feed 113
- Connector 114
- Cassette Feeder Board 114
- Cassette 116
- Cassette Pickup 117
- Connector P201 118
- Cassette Pickup Rollers 121
- Roller Shaft 122
- Pickup Roller Shaft 124
- Cassette Feeder Roller 127
- Fuser Assembly 130
- Fuser Top Cover 132
- Fuser Pressure 134
- Fuser Paper Guide 136
- Delivery Sensor 138
- Temperature 140
- Sensor Assembly 140
- 1 Remove the six screws 141
- Fuser Heater Bulb 142
- Right Fuser 143
- Fuser Heater 145
- 3 Remove the screw and 148
- I/O Shield 149
- Take Apart I/O Shield - 55 150
- 1 Remove the six mounting 150
- I/O Controller 151
- P119P50 P51 156
- I/0 Controller Mount 156
- I/O Controller Mount 158
- DC Controller 159
- P18 P14 P15 P17 P16 P19 164
- High-Voltage 167
- Power Supply 167
- 3 Remove the five screws 169
- Power Switch 170
- Left Top 171
- Front Access Door 172
- Power Switch Lever 172
- 5 Remove the two screws 173
- Contact Assembly 174
- Cable Retainer 175
- 3 Cut the wire tie, remove 176
- Take Apart Power Supply - 84 179
- 4 Remove the three screws 179
- Take Apart Fan - 86 181
- 1 Disconnect connector 181
- P18 from the DC 181
- Take Apart Fan - 87 182
- 2 Remove the two screws 182
- Drive Assembly 183
- 1 Remove the two screws 184
- 2 Disconnect connector 185
- P14 from the DC 185
- Main Motor 187
- Scanner Motor 189
- Toner Cartridge 192
- Black Plastic Cover P118 193
- Black Plastic Tab 194
- 5 Lift out the toner 195
- Double Gears 196
- Double Gear 197
- Snap Ring 197
- Snap Ring Pliers 197
- Transfer Roller 198
- Paper Charge 200
- Deflector 200
- 1 Grasp each end of the 201
- Ground Wire 202
- Paper Charge Deflector 202
- Paper Feed Roller 203
- Paper Separation 205
- Manual Feed 206
- Pickup Plate 206
- Separation 206
- 3 Lift the paper separation 207
- Pickup Rollers 209
- E-RingE-Ring 210
- 4 Slide the left and right 211
- Paper Separation Assembly 212
- Paper Delivery 213
- 2 Pull up each side of the 215
- Door Cap 217
- Front Access 217
- 1 Remove the four screws 218
- LED Assembly 219
- Release Latches 220
- Pickup Roller 224
- 1 Remove the two 225
- Manual Feed Sensor Spring 227
- Sensor Arm 228
- Manual Feed Pickup Plate 228
- Pickup Solenoid 232
- P17 DC Controller 233
- 4 Remove the mounting 235
- Door Assembly 236
- 6 Using a jeweler's 239
- Laser/Optic Assy 241
- Upgrades 242
- Upgrading RAM 243
- PhotoGrade 244
- Medallion 244
- Placement 245
- Fax Card Upgrade 247
- Metal Shield 248
- I/O Bracket 248
- Fax Card 249
- Phone Connector 249
- LW Select 310 250
- Optional Feeder 253
- 3 & 4 254
- Exploded View 255
- Exploded View 1 256
Prodotti e manuali riguardandi Stampa e scansione Apple LaserWriter Select 310
Stampa e scansione Apple Color Printer Specifiche
(166 pagine)
(166 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale